Best Handy Tips to Troubleshoot an Internet Connection


This safe and reliable step-by-step guide explains its valuable users, how to set up a broadband router for home computer networks safely and securely. The correct and accurate names of configuration settings on these routers vary depending on the particular model or manufacturer. However, this process allows to access mywifiext for netgear extender login. For this, what you have to do:

  1. Choose an Appropriate Location

Consider choosing a suitable location for your router for its installation and configuration in an open floor, table or an airy room. This does not suppose to be the permanent location. Also, remember that wireless routers sometimes need careful positioning and deployment in places hard to reach. So, it is best to choose a location where it’s easiest to work with the router and worry about final placement later on or afterward.

  1. You need to Put the Power on

Firstly, plug in your router into an electric wall socket, and then turn on the router by pushing the ‘power button’.

  1. Connect Your Internet Modem to the Router via Ethernet Cable

You might want to know the fact that older network modems connect via an Ethernet cable but USB connections have become gradually more common. On the other hand, the cable plugs into the router jack named ‘WAN’ or ‘uplink’. Well, when connecting devices with network cables, be sure that each end of the cable connects physically and properly with each other. Wobbly or loose cables are one of the most common sources of network setup problems and issues. After connecting the cable with each other, be sure to power cycle (turn off and turn back on) the modem to ensure the router recognizes it completely. Always remember that this process is a lot helpful in new extender setup.

  1. Connect a Computer to the Router

Router is the main element of your home networking system. For this process, you have to first connect a computer to the router via Ethernet cable. Remember, using the WiFi connection of a wireless router for initial installation is not recommended for the WiFi settings. Well, temporarily using a cable for router installation avoids dropped or unstable connections.

Note: After the installation of your router, the computer can be changed over to a wireless connection as required.

  1. Open the Console Page of Router’s Administration

Now, what you have to do, from the computer connected to the router, open a Web browser onto it. After that, enter the router’s address for network administration in the address field and hit enter in order to reach the router’s administration home page. Well, countless routers are reached by either the Web address (by default). So, it is strictly recommended that consult your router’s documentation to determine the exact address for the model number of your device.

  1. Log In to your Device Home Page

Remember, the router’s home page will prompt for a username and password (default). Both are provided in the router manuals. It is also recommended that change the router’s password for security reasons, but do this after the installation is complete to avoid unnecessary complications.

  1. Enter ‘Internet Connection’ Information

In case, you want your router to connect to the internet, then enter ‘internet connection’ information into that section of the router’s configuration home page.  Suppose, if you are using ‘DSL Internet’ often require entering ‘PPPoE’ username and password settings. Similarly, if you requested and have been issued a ‘static IP address’ by your internet, the static IP settings (including network mask and gateway address) supplied by the provider supposed to be set in the router (reliable and secure).

  1. Update the Router’s MAC Address

A number of ‘internet providers’ in today’s modern world authenticate their customers by ‘MAC addresses. If you are making use of an older network router or other gateway devices to connect to the internet, then your provider may be tracking that ‘MAC address’ and prevent you from going online with the new, latest and updated firmware of the router. On the other hand, if your Internet service has this restriction, you can update the IP address of the router with the MAC address of the device you were using previously. For more information, help and assistance call our customer care desk on toll-free number.

Read also –

  1. Change the Network Name (SSID) 

It may interest you to know that routers come from the manufacturer with a default name chosen, but there are advantages to using a different name as a substitute. So, it is strictly recommended that do not leave the SSID as default. Create it to something strong and reliable soon after the process of configuration and linksys extender setup.

  1. Confirm the ‘Local Network Connection’

First of all, verify the local network connection between your computer and the router whether they are working properly or not. For this, what you can do, check that your computer has received valid IP address information from the router or not.

  1. Confirm that your Computer can Connect to the Internet or Not

First of all, what you have to do, open a Web browser of your choice and visit internet sites such as For more information, visit us or call our tech support team immediately.

12.Connect an Additional Computer with the Router

While connecting from a wireless device, be certain about the network name. It is also known as ‘Service Set Identifier’ (SSID).

  1. Build up ‘Network Security Feature’

Consider configuring additional network security features as needed to guard your systems against unauthorized source and unidentified people. Such WiFi ‘Home Network Security’ Tips contain a checklist to follow and keep you and your networking devices away and safe from malicious group and natives.

Related Posts